GM Retains Silverado and Sierra Cylinder Deactivation After Supplier, Spring Fixes
General Motors is carrying its familiar cylinder-deactivation lifters into the 2027 Chevrolet Silverado 1500 and GMC Sierra 1500, despite acknowledged failures in earlier customer V8s. Rather than replace the underlying architecture, GM says it addressed two contributors through supplier changes and an improved spring inside the lifter.
Ian Stahl, a GM assistant chief engineer, provided that account in an interview published November 5, 2026. He attributed many failures from roughly four or five years earlier to poorly formed wire supplied to GM. The company changed suppliers approximately four years ago, he said, and has since recorded little related warranty activity. GM has not released claim totals or failure rates that would quantify that improvement.
Stahl also described a correction to a spring within the lifter’s switching mechanism. He said GM regards the system as sound and characterized the problem as one he thinks is now behind the company. His explanation identifies causes behind many earlier cases, rather than assigning every historical lifter failure to the same wire or spring problem.
An earlier service action shows the spring’s practical significance
A 2021 GM service update described by GM Authority provides useful context for the spring issue. Service update N212353840 covered certain 2021 full-size trucks and SUVs with the 5.3-liter L84 or 6.2-liter L87 V8. It identified a potentially broken valve-lifter lock-pin spring and instructed dealers to replace lifters on both cylinder banks before affected vehicles were sold.
That dealer action was limited to the specified vehicles and does not define the cause or scope of every customer failure. It does, however, document how a small spring inside the deactivation hardware could justify extensive engine work. The published update did not state how many vehicles required repair.
The component’s importance comes from the way GM’s pushrod V8 changes operating modes. Under ordinary operation, a hydraulic lifter transfers camshaft movement through a pushrod to open a valve. During cylinder deactivation, the lifter body continues following the camshaft while the pushrod remains stationary, interrupting that motion so the valves stay closed.
As Clemson University’s overview of cylinder-deactivation systems explains, the engine also cuts fuel to selected cylinders. The remaining cylinders work at a higher load, which can reduce pumping losses when the engine does not need full output. Some overhead-cam engines accomplish the same broad task through specialized rocker arms or movable camshaft elements, but GM’s pushrod arrangement places the switching function in hydraulic lifters.
Why GM kept the mechanism
Retaining the architecture preserves an efficiency tool that can adapt the number of firing cylinders to immediate torque demand. A 2018 engineering simulation study of cylinder deactivation estimated fuel-economy improvements of 2.2% to 12.9%, depending on the vehicle, displacement, engine load and control strategy. Those figures are not measurements of the 2027 GM trucks, but they show why the value of deactivation varies greatly by application and operating condition.
GM expects its larger 2027 V8s to create more opportunities for reduced-cylinder operation. The 5.7-liter L76 replaces the 5.3-liter engine and produces 402 horsepower and 428 pound-feet of torque. The 6.6-liter L78 replaces the 6.2-liter V8 and produces 481 horsepower and 501 pound-feet. Both gain displacement through a 6-millimeter increase in piston stroke.
Stahl said the resulting increase in torque from each cylinder should allow the engines to remain in reduced-cylinder modes longer. Fewer firing cylinders can satisfy a given request when each active cylinder contributes more torque, although actual operation will still depend on load, speed, truck configuration and calibration.
That engineering rationale does not guarantee a better fuel-economy rating for the complete vehicle. Reported EPA comparisons compiled by MotorTrend show generally lower 2027 ratings than for equivalent 2026 Silverado and Sierra configurations, often by one or two miles per gallon and by more in some diesel variants. Changes in displacement, output, drivetrain and trim prevent those comparisons from isolating the effect of cylinder deactivation.
For owners, GM’s account is more specific than a broad assurance: supplier wire formation and an internal spring were identified as contributors, and corrective changes followed. Still undisclosed are the affected supplier names, revised part numbers, an exact production cutoff and quantified warranty results. Long-term service data from the 2027 engines will ultimately show whether those targeted corrections are enough for the lifter architecture GM chose to retain.
| More aerospace and engineering stories, right in your MSN feed. Follow AMI on MSN |
By Thomas Caldwell — AMI’s senior editor for mechanical and mobility engineering, covering vehicle electronics, systems integration, electrification, chassis systems, propulsion, and safety policy.
